
Sieves
Conforming to the specifications and tolerance in accordance to I.S. 460 for fine materials made out of 20cms. Diam spun type joint less polished brass frame easily fit on each other equipped with stainless-steel wire mesh aperture size
Product Code : SAMS CVL - 029
Send A EnquirySOIL HYDROMETER
Conforming to the specifications and tolerance in accordance to I.S.2720 Part-IV and 3104 used for the grain size analysis of soils where more than 10% of the material will pass through 75microns I.S. SIEVE. Manufactured from clear transparent glass having uniform clarity throughout the upper end on which density scale is engraved.
Product Code : SAMS CVL - 030
Send A Enquiry

Softening Point Apparatus Ring
Conforming to the specifications and tolerance in accordance to I.S.2720 part-v and latest I.S.9259.Consists of a hard rubber base carrying a sliding carriage assembly to which a brass cup is hinged. The cup is raised and allowed to fall through a height of 1cm by the help of a lead screw provided at the back of the sliding carriage.
Product Code : SAMS CVL - 031
Send A EnquiryLIQUID AND PLASTIC LIMIT APPARATUS
Conforming to the specifications and tolerance in accordance to I.S.-2720 consists of followings:-Glass plate 20cm x 15cm. with ground edge, Stainless steel spatula 2cm. wide and 8cms. Long with wooden handle, Brass rod 3mm. dia, Measuring cylinder 25 ml x 0.5 ml graduations.
Product Code : SAMS CVL - 032
Send A Enquiry

SHINKAGE LIMIT APPARATUS
Conforming to the tolerance and specifications in accordance to I.S.2720 part-vii, for the determination of the water content level after which any further reduction in the water content will not cause a corresponding decrease in the volume of the soil mass.
Product Code : SAMS CVL - 033
Send A EnquiryProctor Compaction Apparatus
Conforming to the specifications and tolerance in accordance to I.S.-2720 Pt.-XV. The equipment consists of followings: - Loading Unit:-maximum capacity 20kg/cm.sq. Consisting of loading yoke connected to a lever arm with a counterbalancing adjustment and having a lever ration 1: 10. The whole assembly being mounted on a steel frame. Consolidation cell assembly.
Product Code : SAMS CVL - 034
Send A Enquiry

DIRECT SHEAR APPARATUS
Conforming to the Specifications and tolerance in accordance to I.S.-2720 Part-XXVIII consists of :- Small sand pouring cylinder 3 liter capacity mounted above a pouring cone and separated as a shutter hole. Cylindrical Calibrating container internal diam 100mm and internal depth 150mm fitted with a flendge 5 cm. wide. Metal Tray 30cms square and 4 cms. Deep with a 10cms. Hole in the centre.
Product Code : SAMS CVL - 035
Send A EnquiryTHERMEOMETER
Used for soil specimen of 38mm diam x 76mm. long Conforming to the specimen and tolerance in accordance to I.S.2720 Part-XII.
Product Code : SAMS CVL - 036
Send A Enquiry

TRIAXIAL SHEAR APPARATUS
Conforming to the Specifications and tolerance in accordance to I.S.-2720 Part-XXVIII consists of :- Small sand pouring cylinder 3 liter capacity mounted above a pouring cone and separated as a shutter hole. Cylindrical Calibrating container internal diam 100mm and internal depth 150mm fitted with a flendge 5 cm. wide. Metal Tray 30cms square and 4 cms. Deep with a 10cms. Hole in the centre.
Product Code : SAMS CVL - 037
Send A EnquiryThree gang consolidation test device
Used for soil specimen of 38mm diam x 76mm. long Conforming to the specimen and tolerance in accordance to I.S.2720 Part-XII.
Product Code : SAMS CVL - 038
Send A Enquiry

Soil Permeability Apparatus
Conforming to the Specifications and tolerance in accordance to I.S.-2720 Part-XXVIII consists of :- Small sand pouring cylinder 3 liter capacity mounted above a pouring cone and separated as a shutter hole. Cylindrical Calibrating container internal diam 100mm and internal depth 150mm fitted with a flendge 5 cm. wide. Metal Tray 30cms square and 4 cms. Deep with a 10cms. Hole in the centre.
Product Code : SAMS CVL - 039
Send A EnquiryTile Abrassion testing machine
The wear of the tile is measured using thickness measuring device (which is supplied at extra cost). TheAbrasion Testing Machine consists of a replaceable grinding path, fitted on to a disc rotating about its vertical axis. A funnel is provided to facilitate charging the grinding path withabrasive powder.
Product Code : SAMS CVL - 040
Send A Enquiry

TILE FLEXURAL TESTING MACHINE
Unit for finding flexural strength of clay roofing tiles and cement concrete flooring tiles. Flexural load is applies on the tiles using lead shots. The machine consists of a stand on which two 40mm dia bearing rollers or 12mm dia rollers are placed at centre distance of 150mm, 200mm, 250mm, or 270mm as the case may be. The third upper roller applies centrally flexural load by means of lever arrangement
Product Code : SAMS CVL - 041
Send A Enquiry