open drum orifice
Main supply tank with orifice & mouthpiece fitting arrangement.
Diameter of Orifice-8.5mm,Diameter of mouthpiece-8.5mm.,Nozzle-25mm.&50mm length.
Tracer pointer with scale.
Measuring tank
Product Code : SAMS HYD - 001
Send A EnquiryPipe fiction apparatus
Sudden expansion-1/2”to 1”
Sudden expansion-1/2”to 1”
Differential manometer.
Measuring tank – 400 x 300 x 300mm
Product Code : SAMS HYD - 002
Send A Enquiry
Notch apparatus
Types of notch : 600 v notch , rectangular notch, Trapezoidal.
Flow channel : 250 x 250x 1250 mm with notches fitting arrangement
Pipes and Valves : 1” G.I. piping and 1” Brass valves.
Water storage Unit : Sump Tank – 900 x 400 x 400 mm M.S. tank with F.R.P. coating. Or S.S. tank.
Product Code : SAMS HYD - 003
Send A EnquiryCentrifugal pump test rig
Measuring tank & stop watch.
Basic piping-1”
Orificemeter & venturimeter
Differential manometer
Product Code : SAMS HYD - 004
Send A Enquiry
Bernoulis theorem
Flow channel : 750mm long with transparent solid acryalic
Pipes and Valves : 1” G.I. piping and 1” Brass valves
Water storage Unit : Sump Tank – 900 x 400 x 400 mm M.S. tank with F.R.P. coating. Or S.S. tank.
Product Code : SAMS HYD - 005
Send A EnquiryFrancis turbine Test Rig
Francis turbine is a reaction turbine which was developed by an English born American engineer Sir J.B Francis. the water enter the turbine though the outer periphery of the runner in The redial direction & leaves the runner in axial direction & hence it is called a mixed flow turbine As the water flow to the the runner a part of pressure energy goes on changing in to kinetic energy. Thus the water though the runner is completely enclosed in a air tight casing & the casing & runner is always full of water.
Product Code : SAMS HYD - 006
Send A Enquiry
Kaplan Turbine Test Rig:
Kaplan wheel turbine is an axial flow reaction tubine named in honour named in honour of Sir L Dr. B. Kaplan, a German Engineer.This tubine suitable low head. The power produced by a proportional to QH. Asa head (H) Decrease the discharge (Q) must increase to produce the same power.
Product Code : SAMS HYD - 007
Send A EnquiryMetacentric Height Apparatus
Semi Circular Sectioned hollow ship model, provision for loading as Cargo and warship, fine arrangement for accurate angle measurement extra weight in Metric Unit for tilting coupled.
Product Code : SAMS HYD - 008
Send A Enquiry
parallel and series pump experiment setup
In complex systems, pumps can be connected in series or in parallel. In serial operation the heads of the pumps are added and in parallel operation the flow rates (capacities) of the pumps are added.
Product Code : SAMS HYD - 009
Send A EnquiryPITOT TUBE APPARATUS
A pitot tube made up of small copper tube is held in a pipe line. A screw type arrangement is provided to raise or lower this pitot tube. The open end is connected to a manometer.
Product Code : SAMS HYD - 010
Send A Enquiry
Hydraulic Flume Apparatus
A hydraulic flume of c/s 200x300 mm & 6000 mm length with transparent window on either sides of 1000 mm length.
Sliding gates one at upstream and other at the downstream side.
Screw jack for change of the slope of the flume.
A Sump tank of sufficient capacity.
Product Code : SAMS HYD - 011
Send A EnquiryFLOW NOZZLE
A flow nozzle meter consists of a short nozzle, usually held in place between two pipe flanges. It is simpler and less expensive than a venturi meter, but not as simple as an orifice meter. The frictional loss in a flow nozzle meter is much less than in an orifice meter, but higher than in a venturi meter.
Product Code : ELSHADDAI HYD - 012
Send A Enquiry
